TJB-INC - Water Garden & Pond Products / Skimmer Units & Replacement Mats, Auto Fills, etc / Aquascape Inc / All Products

Aquascape's Pond Owners Manual For Water Garden & Pond Lovers

Sat, 23 Mar 2013 10:08:00 GMT

Aquascape's Pond Owners Manual For Water Garden & Pond Lovers
Buy Now: $3.99

Aquascape's

Pond Owners Manual

We offer a copy of the full color, 24 pg "Pond Owner's Handbook" in both as a printed booklet and as a download in a .pdf. This handbook covers all of the topics that a pond owner will need to know about.

Pond Ecology & the Aquascape System
Pond Fish - Health & Care
Aquatic Plants
Pond Myths
Maintenance
Pump Trouble Shooting

To download the .pdf file, CLICK HERE.

To view more Aquascape videos CLICK HERE

Visit Aquascape Inc to see additional products in this category.

Quick Connector for 1/4" Poly Tubing use with the Aquascape Hudson AutoFill Valve

Thu, 2 Sep 2010 08:59:00 GMT

Quick Connector for 1/4" Poly Tubing use with the Aquascape Hudson AutoFill Valve
Buy Now: ~~$7.99~~ $6.99

Quick Connector for 1/4" Poly Tubing

Straight Union Connector - Connects tube to tube using SpeedFit Quick Connectors.

Used with Aquascape Hudson Water Fill 1/4" tubing
Cut the end of the tube square ensuring it is free of score marks and burrs. Slip all of the way into and it locks shut.
Easy to remove and reuse

Visit Aquascape Inc to see additional products in this category.

Aquascape Signature Series Skimmer - Weir (flap) & Weir Plate Assembly for the 6.0 & 8.0 Skimmers

Fri, 14 Mar 2008 06:28:00 GMT

Aquascape Signature Series Skimmer - Weir (flap) & Weir Plate Assembly for the 6.0 & 8.0 Skimmers
Buy Now: ~~$54.99~~ $49.49

Replacement Weir Plate & Weir

Aquascape Signature Series Skimmers 6.0 & 8.0

Available in 6" for the 6.0 Skimmer
Available in 8" for the 8.0 Skimmer
Includes Mounting Plate & Weir (center flap)
Weir (center flap) available separately if needed

To increase your skimmer's maximum water flow from 4,000 gallons per hour on the 6.0 skimmer, to a maximum of 10,000 gallons per hour on the 8.0 skimmer, just change the Weir Plate Assembly from the 6.0 to the 8.0. All of the screws will match up perfectly. The skimmer housing (box) is the same for both skimmers. You will need to drain the pond's water level down below the base of the skimmer so you can work with dry materials. Unscrew the 6.0 weir from the front of the skimmer and pull the EPDM liner off of the skimmer's face. Then you will have to remove any remaining black silicone from the liner and the skimmer's face. Take the new 8.0 weir assembly and cut your liner to fit the new 8" opening. Apply a fresh bead of black silicone around the skimmer's face and over the open screw holes. (See enclosed weir plate instructions for more information if necessary) Now attach the 8.0 weir plate with the screws, tighten, and wait 30 minutes before refilling pond water. Now you can increase the size pump up to 10,000 GPH.

Visit Aquascape Inc to see additional products in this category.

1/4 x 1/4 Quick Connectors - Aquascape Automatic Water Fill Valve for Water Garden & Pond Skimmers

Sat, 27 Oct 2007 10:37:00 GMT

1/4 x 1/4 Quick Connectors - Aquascape Automatic Water Fill Valve for Water Garden & Pond Skimmers
Buy Now: $5.49

Automatic Water Fill Valve - 1/4" x 1/4" Quick Connectors

Quick connectors to connect ¼" pipe to ¼" pipe
No tools required
Click on "View Enlarged Image" for instructions

Visit Aquascape Inc to see additional products in this category.

Aquascape Signature Series Mechanical Water Garden & Pond Skimmers

Tue, 9 Oct 2007 16:29:00 GMT

Aquascape Signature Series Mechanical Water Garden & Pond Skimmers
Buy Now: ~~$279.98~~ $223.98

Signature Series Skimmers

The first step in building a pond is ensuring that waste products are efficiently removed from the system. The application of a skimmer and bottom drain is essential in this regard.

Skimmers can remove as much as 85% of debris before it settles to the bottom and is the most effective way of reducing maintenance and increasing the quality of your water. They can provide both mechanical and biological filtration all in one unit. It provides efficient removal of floating debris and oxygen robbing protein film. A leaf trap is included and offers easy removal of larger debris. Everything is removable for easy access and maintenance. The door automatically adjusts to the pond water level for more suction. The floating door prevents most fish from entering the basket.

The addition of a skimmer will greatly reduce the maintenance and increase the enjoyment of your pond.

MicroSkim

Ideal for ponds up to 1000 Gallons
Durable Lid- Provides protection of the filter components
Debris Net - Traps larger leaves and debris
Filter Brushes - Provides additional mechanical filtration
Skimmer Door - Skims the surface of the pond
MicroSkim - Housing design is rounded, creating strength and durability
Offers professional grade features and quality for the DIY market
20" deep x 17.5" high x 17.5" wide

Signature Series Skimmer Includes:

A mechanical filter with a new, large-volume, rigid debris basket.
Stainless steel hardware provides resistance to corrosion.
Molded stainless steel insert ensures easy attachment.
Special designed filter mat (with pre-punched knock-outs for check valves).
The Signature Series Skimmer is designed to handle up to two horzontal Aquascape Pumps up to 7500 GPH each.
The Adjustable Faceplate allows four inches of travel to enable you to tweak out the perfect water level.
New injection molded fittings for check valve threads into pump and blkhead, providing professional, watertight seal along the back of the filter.
Includes Rigid Debris Basket, and Natural Looking Faux Rock Lid!
This Skimmer has easy maintainence, upgraded hardware from the other ADI Skimmers.
A new US Patent is pending for the adjustable faceplate!
This skimmer was created from the feedback that ADI received from installation contractors in the field.
We wanted a D-Shape box that would not collapse under pressure, multible pipe inputs, a more realilist rock lid, an adjustable face plate, better debris collection device, & better mats to catch debris.
ADI listened and created the Signature Series line of professional pond products. The top-of-the-line products available today for water garden construction.
Signature Series Skimmer 6.0 has a 6" weir openning and can handle flow rates up to 4,500 GPH.
Signature Series Skimmer 8.0 has an 8" weir openningcan handle flow rates up to 10,000 GPH.
The ADI 10,000 does not fit into the Signature Series Skimmer. When 10,000 GPH is desired, we suggest using multible pumps or use Aquascape Classic Grande Skimmer)
To view the written Signature Series Skimmer Instruction Manual (English & French) in a Down-loadable PDF file that can be printed, click on the link "DOWNLOAD WRITTEN INSTRUCTIONS"
To view the written Signature Series Check Valve Instruction Manual (English only) in a Down-loadable PDF file that can be printed, click on the link "DOWNLOAD MANUAL"

Visit Aquascape Inc to see additional products in this category.

Aquascape 1/2" Hudson Automatic Water Garden Fill Valve for Mechanical Water Garden Skimmers

Tue, 9 Oct 2007 16:28:00 GMT

Aquascape 1/2" Hudson Automatic Water Garden Fill Valve for Mechanical Water Garden Skimmers
Buy Now: ~~$89.99~~ $71.99

1/2" Hudson Water Fill Valve

The Hudson Valve, with its new and innovative design, will solve your fluid control problems once and for all. This compact, virtually indestructible valve is well adapted to a wide variety of applications, from personal home use to large-scale industrial use. This valve is ideal for any application where it is necessary to control the level of fluid. The Hudson Valve's unique design has caught the attention of people in every type of industry where fluid control is necessary.

For use with Aquascape's Signature, Classic (Standard, Large, & Grande), and Micro Skimmers
Compatible with Pondless Waterfall MicroSnorkel Vault.
Will work on other manufacturer's skimmers as well
Special Aquascape Watergarden Mounting Plate.
High Volume Flow Rate.
Click on "View Enlarged Image" (below picture) for flow chart in GPM..
Easy to Install and very reliable.
Allows 4 inches of height adjustment.
For use with our 1/4 inch poly pipe (sold separately).
Can also be used with 1/2 inch pipe by removing the 1/2" to 1/4" quick-adapter on the top of the unit.
Fittings sold separately.

To view the written Hudson Waterfill Valve Instruction Manual (English & French) in a Down-loadable PDF file that can be printed, click on the link at the end of this statement. When you are finished with the PDF file , click your browser's BACK arrow (located in the upper left corner of your screen) to return to this page. "DOWNLOAD MANUAL"

TROUBLE SHOOTING GUIDE

How does the valve work?

The valve operates using a float and a control diaphragm chamber. When hooked up to a water source the valve will allow water to flow through it until the water reaches the bottom of the valve. As the water level rises it causes the float inside of the valve to rise allowing the diaphragm chamber to fill and close the valve.

What type of tubing/pipe should I use to install my Hudson Valve?

Make sure that your tubing/pipe is of an adequate size:

• For the ½” Valve – no smaller than ¼” and no bigger than 1”
• For the 1” Valve – no smaller than ½” and no bigger than 2”

How do I install my Hudson Valve?

• Do not use pipe compound.
• Use plumber’s Teflon tape on threads of water supply pipe.
• Screw Hudson Valve on to water supply pipe; hand tighten only.
• Turn water source on full volume.
• Make sure valve is mounted stably – the valve will not work if it is not secure.
• The valve cannot be submerged.
• The valve must be mounted vertically.

Where will the valve shut off?

(click for photo)

• The valve will shut of about 1 ½”- 2” up from the bottom of the valve depending on pressure (the higher your water pressure the higher up on the valve the water will shut off).
• NOTE: there will be a short delay in shut-off the first time the valve is used while the control chamber fills with water.

Will my valve work in liquids other than water?

• The Hudson Valve is designed to be used in water.
• We only recommend using it in water.
• We will only warranty valves that have been used in water.
• This is not to say that the valve will absolutely not work in other liquids. We have customers that use it in a variety of liquids, but we have not tested it in anything other than water, and thus cannot recommend its usage with any other liquids.
• We do know the valve will not work with salt water as the supply source.

Why won’t my valve shut off?

• The valve needs to be cleaned periodically depending on the cleanliness of the water source.
• Wash the valve and valve parts with fresh water. Dirt, rust, sediment and sand can build up on the valve and cause it to malfunction.
• The valve has two very important holes that run through the center of it. If either of these holes becomes clogged, the valve will not shut off.

To check the holes take the valve apart:

   •Remove the strainer cap from the stem of the diaphragm. (click for photo)
   •Hold the diaphragm up to the light and make sure that the hole that runs through the body of the stem is free and clear. (click for photo)
   •Drop the float out of the body of the valve. To do this, turn the valve upside down. Use a flat head screwdriver and gently push down and out on the clip. (click for photo)
   •Hold the body up to the light and make sure that the hole that runs through the body of the valve is free and clear. (click for photo)
   •If either of these holes is clogged, flush it out with water or use a small needle to help clear the hole. Do not force any object into either hole, as the valve will not work if the size of the hole is altered.

• Check to make sure that you have adequate flow. The valve has to have more than a trickle of water coming to it in order to get it to shut off. If you have less than 10lbs of water pressure, your valve may not be getting enough flow to it to make the valve seal.
• Make sure that your water source is turned on full volume.
• Make sure that your tubing/pipe is of an adequate size:
   •For the ½” Valve – no smaller than ¼” and no bigger than 1”
   •For the 1” Valve – no smaller than ½” and no bigger than 2”
• Make sure that all parts are installed correctly.
   •The screen is installed from the top of the cap down. (click for photo)
   •The diaphragm “skirt” sits in the groves of the body of the valve. (click for photo)
   •The retainer ring sits on top of the diaphragm, with the flat side up. (click for photo)
   •The float has free movement in the body of the valve (using your fingers, gently push the float up and let it drop back down – it should move up and down freely about an 1/8”.
• Do not glue any parts together
• Use Teflon tape only – do not use other products to install valve.
• If you are using a ½” valve, try removing the screen. Due to the fact that there is less area in the ½” valve between the cap and the diaphragm than there is in the 1” valve, the screen on the ½” sometimes will restrict the movement of the diaphragm. Not using a screen will not affect the performance of the valve. The screen is only needed to help filter out debris. If your water source is clean, it is not needed.

Why won’t my valve open?

• The insert in the body of the valve may be clogged. To check this, remove the cap from the top of the valve. Remove diaphragm and retainer ring. Turn valve over and remove clip (you can use a flat head screwdriver and gently push down and out to do this) and drop float out of the body of the valve. (click for photo)
•Hold the valve up to the light and look through the metal insert in the center of the body. If it is clogged, flush is out with water. If this doesn’t clear the insert, use a small needle to gently push the debris out. Then flush with water again to clean. (click for photo)
• There isn’t enough water flow coming to the valve. Your water source must be turned on full volume. We recommend having at least 8 lbs of pressure.

How do I repair my Hudson Valve?

• If none of the following suggestions work, a repair kit will be needed.
Hudson Valve and our many of our distributors sell repair kits containing all of the internal parts of the valve. Please refer to our products page to learn more about repair kits.
• First, try taking the valve apart and cleaning all parts and the body of the valve in clean water.
• Check the hole in the body of the valve. The valve has two very important holes that run through the center of it. If either of these holes becomes clogged, the valve will not shut off.
• To check the holes take the valve apart.
   •Remove the strainer cap from the stem of the diaphragm. Hold the diaphragm up to the light and make sure that the hole that runs through the body of the stem is free and clear. (click for photo)
   •Drop the float out of the body of the valve. To do this, turn the valve upside down. Use a flat head screwdriver and gently push down and out on the clip. (click for photo)
   •Hold the body up to the light and make sure that the hole that runs through the body of the valve is free and clear. (click for photo)
   •If either of these holes is clogged, flush it out with water or use a small needle to help clear the hole. Do not force any object into either hole, as the valve will not work if the size of the hole is altered.
• Check the shut-off pad, which is located on the top of the float (part P07), for any indentations or tears. If it looks dented or torn, try turning it over. You can do this by gently slipping it out of its base using a small needle. Then flip it over and push it gently back in using your finger.
• Do NOT glue, hammer or alter the valve or valve parts in any way. Doing any of this will nullify your warranty.

After I install the valve, what do I do if I hear water hammer or other noise in my line?

• The water hammer can be caused by too much pressure build-up behind the valve. Under high-pressure conditions, installing a pressure-reducing valve before the Hudson Valve may alleviate the problem.

When do I use a continuous flow disc?

(click for photo)

• The continuous flow disc is designed to be used only during the winter in freezing climates. When installed, it will allow the valve to keep a slow trickle of water moving through it at all times. When installed, the valve will not fully shut off. The purpose of this disc is to prevent freezing of pipes during the winter.
• When using a continuous flow disc, you will need an overflow line to take excess water away as the disc will allow the valve to overflow the tank.

Visit Aquascape Inc to see additional products in this category.

Aquascape - 1 1/2" Plumbing Assembly for use with MicroSkim Water Garden & Pond Skimmers

Tue, 9 Oct 2007 16:28:00 GMT

Aquascape - 1 1/2" Plumbing Assembly for use with MicroSkim Water Garden & Pond Skimmers
Buy Now: ~~$44.98~~ $35.98

1½" Plumbing Assembly for use with MicroSkim

This plumbing assembly allow the easy junction between the pump and the Kink-Free Piping that are used in the MicroSkim.
The easy to turn coupler allows for easy pump removal for service or storage while leaving the piping intact.

Visit Aquascape Inc to see additional products in this category.

1/4 x 100 ft Poly Pipe for 1/2" Hudson Automatic Water Fill Valve for Water Garden & Pond Skimmers

Tue, 9 Oct 2007 16:28:00 GMT

1/4 x 100 ft Poly Pipe for 1/2" Hudson Automatic Water Fill Valve for Water Garden & Pond Skimmers
Buy Now: ~~$21.99~~ $19.79

1/4 inch x 100 ft Poly Pipe

¼" x 100 ft. poly pipe is extremely flexable making it easier to install and hide than the 1/2 inch irrigation pipe.
The 1/2" Hudson Automatic Water Fill Valves (sold seperately and available on our Store) new injection molded slide plate is now very easy to install,
Allows 4" of on/off adjustment and improves structural support of the valve housing. (A great improvement over our previous model.)
500 gallon per day fill rate with the ¼ poly pipe provides more than enough water to keep up with evaporation on residential size projects.
New water spigot fitting has quick-connect adaptor for 1/4" poly and is manufactured out of brass for durability (sold seperately on our Store).
New 1/2 inch conversion kit allows Water Fill Valve to be adapted to conventional irrigation lines (sold seperately on Store).
For use in Micro, Standard, Large, Grande, and Signature Series Skimmers. Also for use with the Pondless Waterfall MicroSnorkel Vault.

Visit Aquascape Inc to see additional products in this category.

Brass Quick Connect Water Spigot Fitting for Aquascape 1/2" Hudson Automatic Water Fill Valve

Tue, 9 Oct 2007 16:28:00 GMT

Brass Quick Connect Water Spigot Fitting for Aquascape 1/2" Hudson Automatic Water Fill Valve
Buy Now: ~~$20.59~~ $18.53

Brass Quick Connect Water Spigot Fitting

This fitting is used to connect ¼ inch poly piping from the 1/2" Hudson Automatic Waterfill Valve to a conventional 3/4" outside water spigot.
No tools needed.
Includes rubber washer for a leak free connection to spigot

Visit Aquascape Inc to see additional products in this category.

Irrigation Conversion Kit (1/2" to 1/4") for Aquascape 1/2" Hudson Automatic Water Fill Valve

Tue, 9 Oct 2007 16:28:00 GMT

Irrigation Conversion Kit (1/2" to 1/4") for Aquascape 1/2" Hudson Automatic Water Fill Valve
Buy Now: $7.99

Automatic Water Fill Valve - Irrigation Conversion Kit (1/2" to 1/4")

New ½ inch conversion kit allows the ½" Hudson Water Fill Valve to be adapted to conventional irrigation lines.
No need to run a line to an outside spigot.
Water Valve is activated every time sprinkler zone is running

Visit Aquascape Inc to see additional products in this category.