Manual 12-Volt Transformers
Transformers for Aquascape LED Pond Lights. All of Aquascape's transformers are designed to be used with both LED or Halogen fixtures. Calculate the total wattage of the fixtures on the project and select the appropriate watt transformer.
- Class II Rated (see info below)
- Simple plug-in transformers provide an economical solution for operating low voltage lighting fixtures.
- Transformer includes a single quick-connect cable port for adding a light.
- Multiple light fixtures can be added by using the 3-Way Splitter (SKU#98489) sold separately.
- No timers or photo-cells. Use a switched outlet, separate timer, or add Aquascape 12 volt Photocell (see related products below)
- Available in 3 different sizes: 6-Watt, 20-Watt, & 60-Watt
- These transformers are UL Listed and can be used outdoors.
- Safe for submersible fixtures
- The 6-Watt has a plug built in to the side of the unit.
- The 20 & 60-Watt have a 6' cord so the transformer can be mounted up to 6' away from the power outlet.
NOTE: These transformers are made for Aquascape LED lights which have a special Quick Connector plug which goes into a special Quick Connector receptacle on the transformer. There are no screw terminals on these transformers. To use with other low-voltage light fixtures, you have 2 options.
- You can purchase the 3-Way Splitter (SKU#98489) and cut off the 3-way splitter end leaving just the special plug thats mates with the transformer and 8" of wire that you can then attach your lights to. (See Related Items Below)
- We offer a Quick Connector Plug with 12" wire leads for and additional $3.50. (Just check the box at the top of the screen).
Low-voltage, systems have several advantages for the home owner: Most important, low-voltage equipment is easier to install. Except for the transformer that's connected to a 120-volt circuit, the entire system runs on harmless 12-volt current. Low-voltage wiring is lightweight and can be laid on the ground or buried just below the surface. Another advantage of low-voltage equipment is that it can be relatively inexpensive. And, when you do the job yourself, the bottom line for low-voltage looks even better. Not only can the capital outlay for a standard high-voltage system be much greater, but you may need to hire a pro for part or all of the installation.
You must size your low voltage transformer to match the combined wattage of the lights or lamps to which the transformer is to supply power plus approximately 25% more for the line.
Sizing your Transformer Example: If you buy a system that comes with six fixtures and each fixture has a 12 watt lamp, then you have a minimum need of 72 watts (12 x 6 = 72). The line itself degrades the wattage as well so as a general rule of thumb you will need to increase it by 25% more. Therefore you'll need at least a transformer that can handle about 90 watts. So a 100 watt transformer would be the minimum needed. If you plan to add additional fixtures in the future, you may want to increase the wattage of the transformer or purchase additional transformers as needed. Keep in mind that the voltage drop over long distances is more pronounced in a low-voltage system, therefore, using wire that's too light (skinny) can affect the output at the lamps and this may adjust the wattage need of your low voltage transformer.
Class II transformers that are pool/spa rated. National Electrical Code 2008
“680.23 Underwater Luminaires.
This section covers all luminaires installed below the normal water level of the pool.
(A) General.
(1) Luminaire Design, Normal Operation. The design of an underwater luminaire supplied from a branch circuit either directly or by way of a transformer meeting the requirements of this section shall be such that, where the luminaire is properly installed without a ground-fault circuit interrupter, there is no shock hazard with any likely combination of fault conditions during normal use (not relamping).
(2) Transformers. Transformers used for the supply of underwater luminaires, together with the transformer enclosure, shall be listed as a swimming pool and spa transformer. The transformer shall be an isolated winding type with an ungrounded secondary that has a grounded metal barrier between the primary and secondary windings.”
