Back

Official Aluminum Greenspeed Regulation Stimpmeter for Golf & Putting Greens

Measures the official "stimp" speed of any golf putting green

In Stock

Price: $102.99

Ship To:

Quantity:

SKU: BAYGC240

Shipping Weight: 5 lb.

Share this product and receive a $1.50 sharing discount.

Limit one sharing discount per purchase.

Sharing Discount has been applied

Tell A Friend

Summary

Bayco Aluminum Greenspeed Stimpmeter

Measures the official "stimp" (ball roll) speed of any golf putting green.
Milled heavy duty aluminum "V" channel construction with ball groove for smooth release.
Tapered end at green side to prevent ball hop
Simply mark a spot on a flat area of the green and place the end of the meter on the mark.
Put a golf ball in the hole of the meter and slowly lift the end of the meter causing the ball to roll out. (Approximately 20 degrees).
Measure the distance the ball rolls from the mark.
Repeat this several times.
Find the average measurement from the different tests. This average number is the stimp meter speed of the putting green.
Used by Golf Superintendents around the world to measure green speeds on their courses.
Take the stimp meter with you to various golf courses to check the stimp speed of their greens.
Learn how to adjust your shots based upon the stimp speed of different greens.
This is a fun tool to have as a training aid, but it can really impress your golf buddies with your knowledge of official green speeds.

EASY TO USE!

How to Use a Stimpmeter/Greenspeed Meter

Equipment Required:

Stimpmeter
Three golf balls
Three tees
One 10- or 12-foot measuring tape
One Data Sheet

Step 1 Select a level area on the green, approximately 10 feet by 10 feet. (A simple means of checking for a level area is to lay the stimpmeter on the green and place a ball in the V-shaped groove - the movement of the ball will indicate whether or not the area is reasonably level).

Step 2 Insert a tee in the green, near the edge of the area selected, to serve as a starting point. Holding the Stimpmeter by the notched end, rest the tapered end on the ground beside the tee, and aim it in the direction you intend to roll the ball. Put the ball in the notch and slowly raise the end until the ball starts to roll down the groove. Once the ball starts to roll, Hold the Stimpmeter steady until the ball reaches the putting surface.

Repeat the same procedure with two more balls, keeping the tapered end on the same spot.

Step 3 All three balls should come to rest not more than 8 inches apart. (Should they be farther apart than that, the Stimpmeter may have moved too much during the series, the balls may be damaged or of inferior quality, or unusual conditions may exist. In any event, a pattern larger than 8 inches is of dubious accuracy, and the three-roll series should be repeated.)

Assuming the balls stop within the prescribed 8- inch limit, insert a second tee in the green at their average stopping point. The distance between the two tees is the length of the first series of rolls.

Step 4 Repeat Step 2, using the second tee as a starting point and the first tee as an aiming point. (In other words, roll a series of three balls along the same line, but in the opposite direction.)

Step 5 Repeat Step 3, thereby establishing the length of the second series of rolls. Step 6 Measure the two distances - for the first series and the second series - and calculate their average. Record this as the speed of the green.

Note: Should the difference in length between the first and second series be greater than 18 inches, the accuracy of the resulting average may be questionable. The area selected for the test may not have been sufficiently level - or sufficiently representative of the green - in which case it is advisable to select another area and repeat the test. Sometimes a green may be so severely undulating or sloping that a level area is simply not available (which the data record should indicate).

Key Things to Remember

Selecting a reasonably level test area is important. Measurements taken up or down a slope, over mounds, etc., will result in misleading data.
Conditions during a test are important. Initially , test your greens under optimum conditions - a cleanly mowed, dry, smooth surface on a calm day. Once this basic speed has been established, you can then document speeds as they vary under unusual conditions: windy days, wet surfaces, non-mowed, recently topdressed , time of day, before and after fertilizer applications, etc. The data thus accumulated will lead to a better understanding of how different management practices affect the speed and consistency of each green on your golf course.
Practice makes perfect. A relatively small amount of practice in using the Stimpmeter will increase the accuracy and consistency of your data.
Keep thorough records. Obviously, complete and accurate record, maintained over extended periods, are the most useful.

What is a Stimpmeter?

The Stimpmeter is an extruded aluminum bar, 36 inches long, with a V-shaped groove extending along its entire length. It has a precisely milled ball-release notch 30" from the tapered end (the end that rests on the ground). The underside of the tapered end is milled away to reduce bounce as a rolling ball makes contact with the green.

The V-shaped groove has an included angle of 145 degrees, thereby supporting a golf ball at two points ½" apart. A ball rolling down the groove has a slight overspin, which is thoroughly consistent and has no deleterious effect on the ensuing measurments.

The ball-release notch is designed so that a ball will always be released and start to roll when the Stimpmeter is raised to an angle of approximately 20 degrees. This feature ensures that the velocity of the ball will always be the same when it reaches the tapered end.

Although the Stimpmeter is sturdily built, it is a precision instrument and should be protected from damage. When not in use, it should be stored in a plastic tube or case. Even relatively slight damage to the release notch or to the groove may cause errors.

The Potential of the Stimpmeter

Once the Stimpmeter is put into use at your course and the resulting information is analyzed and acted upon, the possibilities for improved playing conditions are virtually endless. Green speeds for individual golf courses should remain up to the course officials, with the input of the superintendent, of each facility.

Stimpmeter Readings on American golf courses generally range from 7 feet to 12 feet, depending on many factors (e.g. Slope, Contours, Green Size, Grasses, Weather, Budgets etc.). Experience shows that trying to keep the speed above 10 feet on a consistent basis usually causes difficult-to-manage turf problems and is not recommended.

The Effects of Management Practices

The manner in which putting greens are managed has a tremendous influence on their speed and consistency. Most of these factors are known to some degree, but almost all are worthy of research. Following are some of the major variables that using the Stimpmeter will help us to understand more effectively:

Mowing height and frequency of cut are extremely important considerations. The mower's bench setting is no guarantee that greens are cut at a prescribed height. More over the condition of the mowers; the type of mowers (floating or rigid cutting units); attachments such as Wiehle rollers, groomers, brushes, and combs; all can make a difference in the cut and green speed. So does double-cutting, verticutting and rolling. The precise effect of each of these factors can be measured with the Stimpmeter.
Watering practices and surface moisture (dew) are crucial to green speeds. Moist turf will be slower than dry turf at any mowing height.
Fertilizing practices can be studied, such as the effects of rate and frequency of application, nitrogen source, and nutrient balance.
Grain is sometimes a deterrent to uniformity of speed. How grain is affected by changes in direction of cut, use of vertical mowing equipment, riding versus single unit mowers, etc., can be studied a they relate to green speed.
The effects of aeration, spiking, and topdressing can be measured, both before and after treatments.
Speed variations among the different grasses presently used for putting greens can be documented.
By keeping good records, you will be better able to observe, determine, and explain variances in green speed throughout the year and compensate for them. For example, in spring, when Poa annua produces excessive seedheads, greens can be slower and more bumpy. Your records will serve as a reminder to topdress, begin vertical mowing, or schedule other practices calculated to help maintain the desired speed and consistency.

General Comments

Knowing the speed of the greens may assist in determining whether a hole location is fair or unfair. A green so fast (or a hole cut in such a position) that a ball cannot be stopped near the hole from any point on the green, for example, is an unfair challenge.

Championship greens should be fast and uniformly paced, firm but resilient. They should place a premium on well-executed shots, while exacting a penalty for less precise shots.

Close daily mowing, a light nutrient program, proper irrigation scheduling, a good topdressing schedule, and a minimum of thatch are the accepted means of achieving excellent greens. The test for determining whether a surface is properly firm but resilient is the type of ball mark that results from a distance shot onto the green. If the turf within the ball-mark depression holds together, the green has the firmness required of a championship green.

Strive for championship conditions only for limited periods of time, principally for important club events. Turfgrass failure is common when championship conditions are maintained for too long or when adverse weather conditions occur.

CUSTOMER REVIEWS (11)

Average Rating: (From 11 Reviews):

Show All New

Green Speed
From Nick Ogilvie of Celina, Texas on 3/8/2022.

Great Stimpmeter
From Anonymous of Jville, Florida on 8/2/2021.

Very well made, precision tool
From Bill of Indianapolis, Indiana on 7/6/2021.

quality product
From Anonymous of TAMPA, Florida on 5/17/2021.

Should not use USPS
From David Roome of Honeoye, New York on 12/28/2020.

Show All New

CUSTOMER QUESTIONS (3)

New

10/19/2012 – Is a stimpmeter a handheld device? (As opposed to a static device with a standard sloping angle that will produce more accurate results)?

Response From TJB-INC: This is a handheld device that can fit into a golf bag. Because the ball is released at the same point where gravity overcomes friction, the results are very accurate. This product is used worldwide to provide stimp readings for published green speeds.

12/13/2009 – Do you know what the stimp speed is for a average amature Colorado course?

Response From TJB-INC: Anywhere from 7 - 9 with 9 being very fast greens.

7/15/2009 – What makes this an "official" Stimpmeter? How does it differ from what the USGA uses? Is it the exact same one that the USGA uses? If not, how is it different? Thanks.

Response From TJB-INC: this is the aluminum version (it is also made in plastic but we do not sell it)that is used to gauge green speed. It is the same one used on golf greens to rate green speed around the world.

New

Returning Customer? Log In | My Account

203-287-0636 | tjb@tjb-inc.com

Use Non-Mobile Version

Back Check Out

Calculate Shipping Redeem Gift Certificate

Privacy Policy Shipping Policy Return Policy

eCommerce Platform by TrueCommerce

Back

Submit Review

Please submit a review of the product Official Aluminum Greenspeed Regulation Stimpmeter for Golf & Putting Greens.

Your Rating:

Review Title: (Example Review Title: Highly Recommended!)

Your Name:

Submit Anonymously

Your City:

Your State/Province:

Your Country:

Your Review:

Submit Cancel

Back

Ask Question: Official Aluminum Greenspeed Regulation Stimpmeter for Golf & Putting Greens

Please ask a question about the product Official Aluminum Greenspeed Regulation Stimpmeter for Golf & Putting Greens.

Your First Name:

Your Last Name:

Your E-Mail Address:

Your E-Mail Address: (Re-type to confirm)

Your Question:

Submit Cancel

Submit Question: Official Aluminum Greenspeed Regulation Stimpmeter for Golf & Putting Greens

Thank you for your question about the product Official Aluminum Greenspeed Regulation Stimpmeter for Golf & Putting Greens.

Back

In Stock Notification

First Name:

Last Name:

Notify me when the Official Aluminum Greenspeed Regulation Stimpmeter for Golf & Putting Greens is in stock.

Submit Cancel

Close

Back

Tell a Friend

Your Name:

Your E-Mail Address:

This address will not be collected or stored

Your Friend's Name:

Your Friend's E-Mail Address:

This address will not be collected or stored

The e-mail to your friend will include standard text from TJB-INC, including a link to the product Official Aluminum Greenspeed Regulation Stimpmeter for Golf & Putting Greens and a picture, if available. If you would also like to include personalized text, please enter it in the box below.

Your Personalized Text: (optional)

Send Cancel