TJB-INC - Landscape Lighting - Solar, LED, & 12-V / Paver, Deck/Dock, Stair & Retaining Wall / Retaining Wall, Column, & Stair Lights / All Products

Replacement - 12 volt WARM LED Module for Wall Eye Lights

Fri, 28 Oct 2016 17:23:00 GMT

Replacement - 12 volt WARM LED Module for Wall Eye Lights
Buy Now: $15.99

WALL EYE ll - REPLACEMENT LED Module- WARM

These LED modules are a direct replacement for the LED unit on any Wall Eye ll Light. The LED module can also be used in many other applications where a low wattage draw fixture is needed to proved light using a 12 volt (AC or DC) power source.

Long Lasting LED's - No more burned out bulbs to replace
Economical - 40,000 Hour Life (almost 14 years @8 hrs lit per day)
Low Power - 2 Watts per unit (2) 1-watt Phillips CMD LED's
Weather Resistant - Sealed & Rustproof, ideal for Outdoor Use
Safe - Cool to the touch ... Low Burn Risk
Long Wire - 72" (182 cm) Lead with UL/18-2 SPT Low Voltage Cable (UL Rated) & 3/8" (1 cm) Stripped and tinned (soldered) for easy connections to power feed cable. Will fit through a ¼" hole.
Veratility - Use with Steps, Walls, Columns or Counter Tops.
Connects to any 12 Volt AC or DC Transformer
Can be retrofitted or installed lower in the wall as well. (See New Design below)
Each Phillips LED Module has (2) 1-Watt flat CMD's (Latest Technology) COOL White LEDs producing 27 lumens @3000 Kelvin with a built in driver/rectifier.
Optimum Voltage is 12 v AC/DC but will operate in a range voltage from 8-12.5 v AC/DC
The weather sealed LED Module is secured by two 3mm x 10mm stainless steel studs with two stainless steel nuts which are included.
Can be used with the original Wall Eye lights (from "Frog Lights LLC"). This new LED Module is a little longer and half the height of the original modules.
Can be used in near fresh & salt water applications

We sell the replacement LED Module in 5 different ways.

LED Module individually with no connectors
LED Module individually with (2) Red Heatshrink waterproof Butt Connectors for use in applications where the original electricial connections are not accessible. For use with 16 & 18 gauge feed wire.
LED Module individually with (2) 3M Silicone filled Connectors for applications where there is easy access to the original electricial connections and new conectors are needed. Use with 14-18 gauge feed wire.
LED Module individually with (2) 3M Scotchlok Insulated Blue Saddle Tap Connectors for applications where there is easy access to the original electricial connections and new conectors are needed. Used for 16 gauge feed wire.
LED Module individually with (2) 3M Scotchlok Non-Insulated Brown Saddle Tap Connectors for applications where there is easy access to the original electricial connections and new conectors are needed. Used for 12 gauge feed wire only.

We now offer a 45-Watt Malibu transformer with a 5' remote photocell (6½"H x 4"W x 3"D) that will power up to (82) Wall Eye lights that we can include in to your order along with a roll of 100" of 16/2 Low-Voltage Cable if you choose. The transformer can set desired turn-on time in 2, 4, 6, 8, or 10 hour intervals after sunset, Dawn to Dusk, or controled by a switched outlet. Add on prices include shipping except to international locations. CLICK HERE

To calculate shipping costs: Add a product to the shopping cart. An orange colored "Calculate Shipping" tab will now show up on the right side of your screen in the blue area in the shopping cart section. Click on this "Calculate Shipping" and enter your zip code. Hit "Submit", and your shipping options & delivery times will now be displayed. If there is a choice, pick the option that best fits your needs.

INSTALLATION INSTRUCTIONS

Do not cut wires yet. Most original LED units will be screwed into the housing with (2) small stainless steel machine screws. Remove the exsisting LED unit from the Wall Eye fixture by removing the (2) screws. Install the replacement LED unit by remounting with the (2) screws. If you have an older Wall Eye unit that did not use screws, then use a knife or screwdriver to pry the old LED unit free from the housing. Make note which side the power wires went. To install a new LED unit, turn the LED unit over so the bottom flat side is facing up. Apply a bead of 1 inch bead of silicone (Window & Door or Kitchen & Bath) to the back of the LED unit. (Like putting toothpaste on a toothbrush.) Now grab the LED unit by the sides and press the bottom with the silicone on to the housing making sure the power wires are going the same way as the original ones did. Use a piece of tape to hold the LED unit in place while the silicone dries (approx 5 hrs).

To make the electrical connections, you have several options.

Lift up the coping or cap to expose the original connection from the LED light to the power cable. Remove the original electrical connectors if possible and remove old LED's wires. Then install the wires from the replacement LED unit into the same connections. Test light before replacing coping or cap.
If the coping or cap is cemented or glued down tight, gently pull on the wires that go into the stone to see if you can pull any extra wire out. Then cut the wires about 3" from the stone. Strip off 3/8" of insulation from the end of the wire. Insert this copper end into the end of one of the RED Butt Connectors. Use a crimper wrench to tightly crimp the wire into the butt connector. (See video Below). Take one of the leads from the Replacement LED unit and cut it to fit leaving 6" of extra length. Remove 3/8" of insullation off this wire as well and then stick it into the open end of the butt connector. Crimp tighly like before securing the wire. Gently pull on the wires to make sure they are secured tightly into the connector. If not, you will have to repeat the process untill you get the connections tight. Using a heatgun, hair dryer, or other heat source, melt the ends of the butt connector so they seal the connections from air and water. Repeat this whole process for the remaining 2 wires. Then, using your fingers, push the extra wire back into the hole in the stone where the original wires came out. Try to get the new butt connectors into the hole so they can not be seen
If you own a soldering iron, you can solder the electrical connections instead of using butt connectors. I would recommend using shrink tubing to cover the soldered connection to prevent oxidation of the wires over time.

Visit Retaining Wall, Column, & Stair Lights to see additional products in this category.

Wall Eye II - 12 volt WARM LED Low-Voltage Landscape Light for Wall, Stair & Column Illumination

Wed, 26 Aug 2015 18:32:00 GMT

Wall Eye II - 12 volt WARM LED Low-Voltage Landscape Light for Wall, Stair & Column Illumination
Buy Now: ~~$56.99~~ $25.00

WALL EYE II^® - WARM LED LIGHTS

For use with any retaining wall, column, counter top, or stair system that has an overhanging top stone or coping that these lights can be mounted under. Provide a WARM white (pure) light (3000 Kelvin) that is aimed down across the front of the face of a retaining wall or column creating wonderful interesting shadow patterns on the face of the stone. The LED's will also provide a lit area in front of the wall & steps as well for safety & security purposes.

AVAILABLE IN 4 DIFFERENT COLORED 1/32" (1 mm) THICK 304 STAINLESS STEEL HOUSINGS:

The Wall Eye II is an improved version of the original Wall Eye light from the now closed company, "Frog Lights". TJB-INC went oversees to create this new updated version which is exclusive to ShopTJB.com in the North Amercian marketplace.

On Sale 8/05/2019 - 08/18/2019 for $25.00 each!

For Wall, Column, & Stair Illumination

Long Lasting LED's - No more burned out bulbs to replace
Economical - 40,000 Hour Life (almost 14 years @8 hrs lit per day)
Low Power - 2 Watts per unit (2) 1-watt Phillips CMD LED's
Durable Construction - Powder Coated 304 Stainless Steel will not Rot or Rust. Can also be used in salt spray applications.
Weather Resistant - Sealed & Rustproof, ideal for Outdoor Use
SAFE - Cool to the touch ... Low Burn Risk
Long Wire - 72" (182 cm) Lead with UL/18-2 SPT Low Voltage Cable (UL Rated) & 3/8" (1 cm) Stripped and tinned (soldered) for easy connections to power feed cable. Will fit through a ¼" hole.
Easy to Install - Simply slip under the cap stone on Block Walls, Columns or Stairs (Before gluing down cap).
Veratility - Use with Steps, Walls, Columns or Counter Tops.
Connects to any 12 Volt AC or DC Transformer
Lightweight but super strong @ 6.5 oz each
No more wasted block from cutting & chiseling like needed for some light fixtures installations!
Installs in Minutes under coping- NO Cutting & NO Drilling!
Can be retrofitted or installed lower in the wall as well. (See New Design below)
Each Phillips LED Unit has (2) 1-Watt flat CMD's (Latest Technology) WARM White LEDs producing 27 lumens @3000 Kelvin with a built in driver/rectifier.
Optimum Voltage is 12 v AC/DC but will operate in a range voltage from 8-12.5 v AC/DC
The weather sealed LED unit is secured by two 3mm x 10mm stainless steel studs with two stainless steel nuts
Space fixtures from 36" to 72" apart (depending upon amount of lighting desired)
Fixture measures: 5 9/16" (15 cm) Wide x 3 1/8" (8 cm) Deep x 1/32" (1 mm) Thick
LED unit & flange stick out 5/8" (2 cm) from the mounted surface with a 1/2" (1.25 cm) reveal
Use with any coping that has a 1" or greater overhang
Units can be painted (by you) to match any decor situation.
PLEASE ... Install & test lights before coping or cap is glued down.
Fixtures Blend into the Landscape (see photos below)
Conforms to UL STD 1838 & Certified to CSA C22.2 No. 250.7
Dealer opportunities available (Contact if interested)
FREE USPS SHIPPING (Lower 48)
NEW DESIGN - Allows you to retrofit lighting into existing installations easily. The Wall Eye II installs into your masonry crack with a simple 7" circular saw with a masonry blade to create the mounting space and a 1/4" masonry bit to feed the wire through.

WALL EYE II has a one year manufactures warrantyhousing & LED failure. Lightning,Power Surges, other natural disasters or vandalism that damage either thehousing and/or LED unit are excluded from the warranty. If there is an LED failure past one year,TJB-INC has replacement LED modules that can be easily replaced by going to www.ShopTJB.com and purchasing the stylerequired for your fixture.

Note: We have had a lot of customers ordering 12/2 wire or thicker because they think these lights have a large wattage draw. This is wrong! Each Wall Eye II LED fixture uses 2 watts each, not 50 watts each. 12/2 wire can be used but is not necessary. 16/2 wire will carry sufficient current to power up to 50 Wall Eye II LED fixtures over a 100' span. Same problem with transformers. Customers are ordering 300 watt & 600 watt transformers to power 20 Wall Eye II LED fixtures. Unless you will be adding additional lights to the transformer, a 45 watt transformer is all that is needed to power 20 WallEye Eye II LED Fixtures. (Just wanted to let you all know before you place your order.)

So ...

We now offer a 45-Watt transformer with a 5' remote photocell (6½"H x 4"W x 3"D) that will power up to (20) Wall Eye II lights that we can include in to your order along with a roll of 100" of 16/2 Low-Voltage Cable if you choose. The transformer can set desired turn-on time in 2, 4, 6, 8, or 10 hour intervals after sunset, Dawn to Dusk, or controled by a switched outlet. Add on prices include shipping except to international locations. CLICK HERE or see Related Products (below)

A Black Wall Eye II is located under the coping in the center of the photo on the right. Photos are of the Cool (4000 K) LED unit but you can see how far the unit lights away from the wall face.

3 Rust (Brown) Cool Wall Eye II's are mounted under the coping of this 1' high display wall.

The night photos were taken in complete darkness at our Display Gardens in Hamden Ct. The photos were take by a non-professional (me) with an automatic digital camera. The Wall Eye cast a wonderful downward light across the face of our tumbled display wall system. The light was a pure white light, not a yellow like halgon bulbs produce. On the larger 3' high wall, the 3' area in front of the wall was also lit up by the LED's from the Wall Eye lights as well as the face of the wall. I spaced the WallEye lights every 6 feet and was able to have the light overlap on the ground.

I was able to reduce the power draw to 12 watts for the 6 lights that I installed, down from the original 60 watts that was there with the 10 watt traditional low-voltage fixtures.

I highly recommend these WallEye lights based upon my experience with many different kinds of lighting fixtures over the past 35 years in business. ... Ted Greiner (President & CEO TJB-INC)

Below are photos showing the difference between the Warm & the Cool LED's. The top set is on a gray colored wall and the bottom set is on a brown colored wall. See how the color of the light makes the wall, pavers, & grass look different. We sell both the lights in either Warm or Cool LED's

Visit Retaining Wall, Column, & Stair Lights to see additional products in this category.

Wall Eye II - 12 volt COOL LED Low-Voltage Landscape Light for Wall, Stair & Column Illumination

Wed, 22 Jul 2015 16:24:00 GMT

Wall Eye II - 12 volt COOL LED Low-Voltage Landscape Light for Wall, Stair & Column Illumination
Buy Now: ~~$56.99~~ $25.00

WALL EYE II^® - COOL LED LIGHTS

For use with any retaining wall, column, counter top, or stair system that has an overhanging top stone or coping that these lights can be mounted under. Provide a COOL white (pure) light (4500 Kelvin) that is aimed down across the front of the face of a retaining wall or column creating wonderful interesting shadow patterns on the face of the stone. The LED's will also provide a lit area in front of the wall & steps as well for safety & security purposes.

AVAILABLE IN 4 DIFFERENT COLORED 1/32" (1 mm) THICK 304 STAINLESS STEEL HOUSINGS:

On Sale 8/05/2019 - 08/18/2019 for $25.00 each!

For Wall, Column, & Stair Illumination

Long Lasting LED's - No more burned out bulbs to replace
Economical - 40,000 Hour Life (almost 14 years @8 hrs lit per day)
Low Power - 2 Watts per unit (2) 1-watt Phillips CMD LED's
Durable Construction - Powder Coated 304 Stainless Steel will not Rot or Rust. Can also be used in salt spray applications.
Weather Resistant - Sealed & Rustproof, ideal for Outdoor Use
SAFE - Cool to the touch ... Low Burn Risk
Long Wire - 72" (182 cm) Lead with UL/18-2 SPT Low Voltage Cable (UL Rated) & 3/8" (1 cm) Stripped and tinned (soldered) for easy connections to power feed cable. Will fit through a ¼" hole.
Easy to Install - Simply slip under the cap stone on Block Walls, Columns or Stairs (Before gluing down cap).
Veratility - Use with Steps, Walls, Columns or Counter Tops.
Connects to any 12 Volt AC or DC Transformer
Lightweight but super strong @ 6.5 oz each
No more wasted block from cutting & chiseling like needed for some light fixtures installations!
Installs in Minutes under coping- NO Cutting & NO Drilling!
Can be retrofitted or installed lower in the wall as well. (See New Design below)
Each Phillips LED Unit has (2) 1-Watt flat CMD's (Latest Technology) COOL White LEDs producing 27 lumens @4500 Kelvin with a built in driver/rectifier.
Optimum Voltage is 12 v AC/DC but will operate in a range voltage from 8-12.5 v AC/DC
The weather sealed LED unit is secured by two 3mm x 10mm stainless steel studs with two stainless steel nuts
Space fixtures from 36" to 72" apart (depending upon amount of lighting desired)
Fixture measures: 5 9/16" (15 cm) Wide x 3 1/8" (8 cm) Deep x 1/32" (1 mm) Thick
LED unit & flange stick out 5/8" (2 cm) from the mounted surface with a 1/2" (1.25 cm) reveal
Use with any coping that has a 1" or greater overhang
Units can be painted (by you) to match any decor situation.
PLEASE ... Install & test lights before coping or cap is glued down.
Fixtures Blend into the Landscape (see photos below)
Conforms to UL STD 1838 & Certified to CSA C22.2 No. 250.7
Dealer opportunities available (Contact if interested)
FREE USPS SHIPPING

NEW DESIGN - Allows you to retrofit lighting into existing installations easily. The Wall Eye II installs into your masonry crack with a simple 7" circular saw with a masonry blade to create the mounting space and a 1/4" masonry bit to feed the wire through.

So ...

We now offer a 45-Watt Malibu transformer with a 5' remote photocell (6½"H x 4"W x 3"D) that will power up to (20) Wall Eye II lights that we can include in to your order along with a roll of 100" of 16/2 Low-Voltage Cable if you choose. The transformer can set desired turn-on time in 2, 4, 6, 8, or 10 hour intervals after sunset, Dawn to Dusk, or controled by a switched outlet. Add on prices include shipping except to international locations. CLICK HERE or see Related Products (below)

A Black Wall Eye II is located under the coping in the center of the photo on the right. Photos are of the Cool (4000 K) LED unit but you can see how far the unit lights away from the wall face.

3 Rust (Brown) Cool Wall Eye II's are mounted under the coping of this 1' high display wall.

I was able to reduce the power draw to 12 watts for the 6 lights that I installed, down from the original 60 watts that was there with the 10 watt traditional low-voltage fixtures.

I highly recommend these WallEye lights based upon my experience with many different kinds of lighting fixtures over the past 35 years in business. ... Ted Greiner (President & CEO TJB-INC)

Visit Retaining Wall, Column, & Stair Lights to see additional products in this category.

Replacement - 12 volt COOL LED Module for Wall Eye Lights

Fri, 29 Aug 2014 11:26:00 GMT

Replacement - 12 volt COOL LED Module for Wall Eye Lights
Buy Now: $15.99

WALL EYE ll - REPLACEMENT LED Module- COOL

Long Lasting LED's - No more burned out bulbs to replace
Economical - 40,000 Hour Life (almost 14 years @8 hrs lit per day)
Low Power - 2 Watts per unit (2) 1-watt Phillips CMD LED's
Weather Resistant - Sealed & Rustproof, ideal for Outdoor Use
Safe - Cool to the touch ... Low Burn Risk
Long Wire - 72" (182 cm) Lead with UL/18-2 SPT Low Voltage Cable (UL Rated) & 3/8" (1 cm) Stripped and tinned (soldered) for easy connections to power feed cable. Will fit through a ¼" hole.
Veratility - Use with Steps, Walls, Columns or Counter Tops.
Connects to any 12 Volt AC or DC Transformer
Can be retrofitted or installed lower in the wall as well. (See New Design below)
Each Phillips LED Module has (2) 1-Watt flat CMD's (Latest Technology) COOL White LEDs producing 27 lumens @4000 Kelvin with a built in driver/rectifier.
Optimum Voltage is 12 v AC/DC but will operate in a range voltage from 8-12.5 v AC/DC
The weather sealed LED Module is secured by two 3mm x 10mm stainless steel studs with two stainless steel nuts which are included.
Can be used with the original Wall Eye lights (from "Frog Lights LLC"). This new LED Module is a little longer and half the height of the original modules.
Can be used in near fresh & salt water applications

We sell the replacement LED Module in 5 different ways.

LED Module individually with no connectors
LED Module individually with (2) Red Heatshrink waterproof Butt Connectors for use in applications where the original electricial connections are not accessible. For use with 16 & 18 gauge feed wire.
LED Module individually with (2) 3M Silicone filled Connectors for applications where there is easy access to the original electricial connections and new conectors are needed. Use with 14-18 gauge feed wire.
LED Module individually with (2) 3M Scotchlok Insulated Blue Saddle Tap Connectors for applications where there is easy access to the original electricial connections and new conectors are needed. Used for 16 gauge feed wire.
LED Module individually with (2) 3M Scotchlok Non-Insulated Brown Saddle Tap Connectors for applications where there is easy access to the original electricial connections and new conectors are needed. Used for 12 gauge feed wire only.

INSTALLATION INSTRUCTIONS

To make the electrical connections, you have several options.

Lift up the coping or cap to expose the original connection from the LED light to the power cable. Remove the original electrical connectors if possible and remove old LED's wires. Then install the wires from the replacement LED unit into the same connections. Test light before replacing coping or cap.
If the coping or cap is cemented or glued down tight, gently pull on the wires that go into the stone to see if you can pull any extra wire out. Then cut the wires about 3" from the stone. Strip off 3/8" of insulation from the end of the wire. Insert this copper end into the end of one of the RED Butt Connectors. Use a crimper wrench to tightly crimp the wire into the butt connector. (See video Below). Take one of the leads from the Replacement LED unit and cut it to fit leaving 6" of extra length. Remove 3/8" of insullation off this wire as well and then stick it into the open end of the butt connector. Crimp tighly like before securing the wire. Gently pull on the wires to make sure they are secured tightly into the connector. If not, you will have to repeat the process untill you get the connections tight. Using a heatgun, hair dryer, or other heat source, melt the ends of the butt connector so they seal the connections from air and water. Repeat this whole process for the remaining 2 wires. Then, using your fingers, push the extra wire back into the hole in the stone where the original wires came out. Try to get the new butt connectors into the hole so they can not be seen
If you own a soldering iron, you can solder the electrical connections instead of using butt connectors. I would recommend using shrink tubing to cover the soldered connection to prevent oxidation of the wires over time.

Visit Retaining Wall, Column, & Stair Lights to see additional products in this category.

Wall Eye II Transformer & Wire Sets

Mon, 11 Aug 2014 08:40:00 GMT

Wall Eye II Transformer & Wire Sets
Buy Now: ~~$96.49~~ $77.19

Wall Eye II Transformer & Wire Set

To help our customers with the correct transformer & wire selection for the Wall Eye II lights that we offer, we have come up with a select transformer and length of wire that will handle most Wall Eye II installations. We have found after 1,000's of sales that most customers want a transformer with lots of featurers so we have selected the MoonRays 100-watt programable because of what it can do.

100-Watt Moonrays Transformer

Old style mechanical dial timer has been replaced by more reliable photocell.
Set desired on time in 2, 4, 6, or 8 hour intervals after sunset, Automatic Dawn to Dusk, or controled by a switched outlet.
No need to adjust for time changes, or seasonal changes of sunset.
Does not need to be adjusted to reset after power outages or daylight savings.
Raintight case and 4ft,18-Gauge power cord ensure safety for outdoor use
Durable plastic construction for lasting outdoor use
Can be mounted to side of a house, deck, or post
UL listed for outdoor installations and mounting
Small Footprint (7¼" H x 5½" W x 4" D)
Can power up to (45) Wall Eye LED Lights
Weight = 7 lbs
1-year limited warranty

16/2 Low Voltage Cable

This wire/cable is used in all low-voltage lighting applications.
Wire = Solid Core & Cable = Stranded Core
We use and sell cable. But not to confuse everyone, we will call it wire because to the common consumer, it it is the same thing.
Our cable is multible stranded 32 gauge copper and remains flexible when cold.
For wire/cable, the lower the wire gauge, the more strands of copper = thicker mass of condutive material and less internal frictional line loss. IE: 16/2 is thicker than 18/2. The first number 16, is the wire gauge. The second number/2, is the total number wire/cable runs attached together as a unit. Low-voltage applications require 2 wire/cable runs. One each to carry the power to your fixtures. 110 volt requires a 3 wire/cable run because building code requires a seperate ground wire that low voltage does not.
Can be used to power our terrestrial & aquatic lighting fixtures.
Rubber insulation has 1 ribbed & 1 smooth side for ease of polarity installations where needed.

Visit Retaining Wall, Column, & Stair Lights to see additional products in this category.

Kerr Lighting 12 Volt StackedStone Wall Lights 4" x 12" For 4" Thick Modular Retaining Wall Systems

Sun, 10 Apr 2011 15:19:00 GMT

Kerr Lighting 12 Volt StackedStone Wall Lights 4" x 12" For 4" Thick Modular Retaining Wall Systems
Buy Now: ~~$34.99~~ $32.00

StackedStone Wall Lights - 4" x 12"

Actual = 4" H x 12 ¼" W x 8" D
The StackedStone Wall Light (also called Natural Impressions) is designed for easy installation into garden wall landscaping projects
Designed to support the weight and pressures of your wall
Strong resin fixtures and lenses designed to be tough enough to withstand UV rays and even light vehicular traffic
Textured lenses help the light integrate with rock-like surface textures to coordinate with many block wall products
Low-voltage system is safe, economical and provides a warm candlelight appearance
Uses (2) 7-watt incandescent bulbs (included)
Easy to install
Each fixture is constructed of the strongest plastic and is designed to interlock seamlessly with 12" x 4" modular retaining wall stones.
Its unique structural design supports the weight and pressures associated with garden walls.
The (2) 7-watt bulbs adds a warm glow to light the way along pathways or driveways, providing an extra element of safety and beauty to your home.
2-Watt LED replacement bulbs available below in RELATED ITEMS
Easy DIY Installation Instructions are included with each order. Replacement parts are always available & in-stock (if ever needed)
TJB-INC supplies free technical help by calling 203-288-3711 or E-Mail : tjb@TJB-INC.com.

Available Sizes:

Individually
4-Pack Installation Kit which include: (4) StackedStone Wall Light Fixtures & Lenses, (8) Sockets, (8) 7-watt bulbs, (8) Wire Connectors, 75 feet of 16/2 outdoor cable, 100-Watt Transformer with Photocell and instructions.
The supplied 12-volt dust-to-dawn transformer can power up to (7) - 14-watt fixtures.
8-Light Pack Bulk Package includes (8) complete fixtures & connectors. (Lights Only! No wire or transformer)
NOTE: Additional cable may be necessary depending on number and spacing of lights. (See Related Products below)
Tools Required: Pliers, Utility Knife, & Star-head Screwdriver.

Installed "Garden Wall Lights" with a 4" high Retaining Wall Stone System

Visit Retaining Wall, Column, & Stair Lights to see additional products in this category.

Kerr Lighting 12 Volt RiverStone Wall Lights 4" x 12" For 4" Thick Modular Retaining Wall System

Sun, 10 Apr 2011 14:59:00 GMT

Kerr Lighting 12 Volt RiverStone Wall Lights 4" x 12" For 4" Thick Modular Retaining Wall System
Buy Now: ~~$34.99~~ $32.00

RiverStone Wall Lights - 4" x 12"

Actual = 4" H x 12 ¼" W x 8" D
The RiverStone Wall Light is designed for easy installation into garden wall landscaping projects
Designed to support the weight and pressures of your wall
Strong resin fixtures and lenses designed to be tough enough to withstand UV rays and even light vehicular traffic
Textured lenses help the light integrate with rock-like surface textures to coordinate with many block wall products
Low-voltage system is safe, economical and provides a warm candlelight appearance
Uses (2) 7-watt incandescent bulbs (included)
Easy to install
Each fixture is constructed of the strongest plastic and is designed to interlock seamlessly with 12" x 4" modular retaining wall stones.
Its unique structural design supports the weight and pressures associated with garden walls.
The (2) 7-watt bulb adds a warm glow to light the way along pathways or driveways, providing an extra element of safety and beauty to your home.
2-Watt LED replacement bulbs available below in RELATED ITEMS
Easy DIY Installation Instructions are included with each order. Replacement parts are always available & in-stock (if ever needed)
TJB-INC supplies free technical help by calling 203-288-3711 or E-Mail : tjb@TJB-INC.com.

Available Sizes:

Individually
4-Pack Installation Kit which include: (4) RiverStone Wall Light Fixtures & Lenses, (8) Sockets, (8) 7-watt bulbs, (8) Wire Connectors, 75 feet of 16/2 outdoor cable, 100-Watt Transformer with Photocell and instructions.
The supplied 12-volt dust-to-dawn transformer with Photocell can power up to (7) - 14-watt fixtures.
8-Light Pack Bulk Package includes (8) complete fixtures & connectors. (Lights Only! no wire or transformer)
NOTE: Additional cable may be necessary depending on number and spacing of lights. (See Related Products below)
Tools Required: Pliers, Utility Knife, & Star-head Screwdriver.

Installed "Garden Wall Lights" with a 4" high Retaining Wall Stone System

Visit Retaining Wall, Column, & Stair Lights to see additional products in this category.

Kerr Lighting 12 Volt Garden Wall Lights 4" x 12" For 4" Thick Modular Retaining Wall Systems

Sat, 22 Sep 2007 11:07:00 GMT

Kerr Lighting 12 Volt Garden Wall Lights 4" x 12" For 4" Thick Modular Retaining Wall Systems
Buy Now: ~~$34.99~~ $32.00

GARDEN WALL LIGHTS - 4" x 12"

Actual = 4" H x 12 ¼" W x 8" D
The Garden Wall Light is designed for easy installation into garden wall landscaping projects.
Designed to support the weight and pressures of your wall
Strong resin fixtures and lenses designed to be tough enough to withstand UV rays and even light vehicular traffic
Textured lenses help the light integrate with rock-like surface textures to coordinate with many block wall products
Low-voltage system is safe, economical and provides a warm candlelight appearance
Uses 7-watt incandescent bulb (included)
Easy to install
Each fixture is constructed of the strongest plastic and is designed to interlock seamlessly with 4" x 12" modular retaining wall stones.
Its unique structural design supports the weight and pressures associated with garden walls.
The 7-watt bulb adds a warm glow to light the way along pathways or driveways, providing an extra element of safety and beauty to your home.
Easy DIY Installation Instructions are included with each order. Replacement parts are always available & in-stock (if ever needed)
TJB-INC supplies free technical help by calling 203-288-3711 or E-Mail : tjb@TJB-INC.com.

Available Sizes:

Individually
4-Pack Installation Kit which include: (4) Garden Wall Light Fixtures & Lenses, (4) Sockets, (4) 7-watt bulbs, (8) Wire Connectors, 50 feet of 16/2 outdoor cable, 100-Watt Transformer with Photo-Cell and instructions.
The supplied 12-volt 100 watt with Photo-Cell dust-to-dawn transformer can power up to (12) - 7-watt fixtures.
8-Light Pack Bulk Package includes (8) complete fixtures & connectors. (Lights only, no wire or transformer)
NOTE: Additional cable may be necessary depending on number and spacing of lights.(See Related Products below)
Tools Required: Pliers, Utility Knife, & Star-head Screwdriver.

Installed Garden Wall Lights with a 4" high Retaining Wall Stone System

Visit Retaining Wall, Column, & Stair Lights to see additional products in this category.

Kerr Lighting 12 Volt 6" x 8" Retaining Wall Lights & Kits For 6" Thick Modular Wall Systems

Sat, 22 Sep 2007 11:07:00 GMT

Kerr Lighting 12 Volt 6" x 8" Retaining Wall Lights & Kits For 6" Thick Modular Wall Systems
Buy Now: $36.50

RETAINING WALL LIGHT - 6" x 8"

Actual = 6" H x 7 7/8" W x 6 1/2" D
The RETAINING WALL LIGHT is designed for easy installation into retaining wall landscaping projects.
Each fixture is constructed of the strongest plastic and is designed to interlock seamlessly with any 6" x 8" modular retaining wall stones.
This light is comparable to the Versa-Lok Cobble Unit
Its unique structural design supports the weight and pressures associated with garden walls.
The 7-watt bulb adds a warm glow to light the way along pathways or driveways, providing an extra element of safety and beauty to your home.
Easy DIY Installation Instructions are included with each order. Replacement parts are always available & in-stock (if ever needed)
TJB-INC supplies free technical help by calling 203-288-3711 or E-Mail : tjb@TJB-INC.com.

Available Sizes:

Individually
4-Pack Installation Kit which include: (4) WALL LIGHT Fixtures & Lenses, (4) Sockets, (4) 7-watt bulbs, (8) Wire Connectors, 50 feet of 16/2 outdoor cable, 100-Watt Transformer with Photo-Cell and instructions.
The supplied 12-volt 110 watt with Photocell dust-to-dawn transformer can power up to (12) - 7-watt fixtures.
8-Light Pack Bulk Package includes (8) complete fixtures & connectors (Lights Only, no wire or transformer)
NOTE: Additional cable may be necessary depending on number and spacing of lights. (See Related Products below)
Tools Required: Pliers, Utility Knife, & Star-head Screwdriver.

Visit Retaining Wall, Column, & Stair Lights to see additional products in this category.